Moj Raptor vsebuje naslednje ...
-
Kasama Head & Fan
Description
FEATURES
* Main rotor hub
o 64 grams
o Machined from 7075 T6 aluminum
o Hub mounts using a pin and clamp design.
+ Clamp design eliminates hub rocking on the shaft yielding crisp, 3D performance.
+ Hub comes with four bearings pre-installed
* Flybar control arm
o 18 grams
o Machined from 7 series aluminum
o The control arm is a single sided design allowing for easier disassembly and adjustment.
* Washout set
o 16 grams
o Mixing arms are machined from 5 series aluminum
+ Washout arms are equipped with set screws to secure the washout linkage pivot pins. (washout links and pivot pins are not included)
+ Flange bearings are included and pre-installed.
+ Washout arms are machined with an additional control hole yielding increased control and response.
o Washout base
+ Machined from 7 series aluminum.
+ Washout base is taller than stock, the result is a wider bearing surface offering smoother, low friction movement.
* Mixing levers
o 12 grams
o Machined from 7 series aluminum
o Flange bearings are included and pre-installed yielding a slop free pivot point.
o Mixing lever length is increased with an additional control hole allowing for more aggressive control.
* Blade grips
o 60 grams- grips, levers and hardware
o Machined from 7075 T6 aircraft aluminum
o Grips are designed to be used with stock raptor bearings (not included)
o Blade grip control arms are offset 3 degrees lower than stock. This allows for more leverage at extreme negative blade pitch angles.
- Quick UK (rep ...)
Machined from solid, this tail casing is lighter than the original plastic unit and offers superb structural integrity.
The tail drive shaft has been centralized, this allows for equal belt clearance within the boom and removes the need for the small "idler" pulley. This unit offers lower weight, less belt drag and greater rigidity, the look speaks for itself !!
Fitted with precision Japanese high duty ballraces and "Holo-Krome" high tensile socket screws.
-Motor OSMax 50 Hyper-Blue Head
SPECIFICATIONS
Stock Number: OSMG1951
Displacement: 0.499 cu in (8.17 cc)
Bore: 0.866 in (22 mm)
Stroke: 0.847 in (21.5 mm)
Practical rpm range: 2,000-20,000
Output:1.9 hp @ 17,000 rpm
Weight: 14.3 oz (406 g)
Includes: 60LH carburetor, #8 glow plug
-Servoti Futaba 3x9252 + 2x9254 Rep/Gas
S9252 .............. S9254 Heli High Torque/High Speed
Volts Torque Speed .............. Volts Torque Speed
4.8V 91.6 oz-in. 0.14 sec/60° ............... 4.8V 47.2 oz-in. 0.06 sec/60°
- Blades Radix 600mm/ V-Blades 600mm / 92mm, Green Paddles (20grams-TT)
- Arizona Regulator + 4800mAh.............
Navodila!
- Governor GV-1 (Futaba) ............
Navodila!
- WildCat Helimix 30% Fuel
HELIMIX is available in FAI, 5%, 10%, 15%, 20%, and 30% Nitro formula. HELIMIX is the premier fuel for R/C helicopters designed to produce maximum tourqe and cooling in the harsh environment of heli flying. Helimix contains 18% oil content and is total synthetic. Helimix was designed as a competition fuel with the aid of competition pilots. Their request was for a fuel that smoked less, made more power, superior mid-range transition, lower heat penalties, and smelled good.